Measure guide · Roller shades

How to measure for roller shades

Pick your mount first. For an inside mount, measure the opening's width in three places and its height in three places, to the nearest 1/8″. Give us the exact numbers; we make the clearance deduction at the factory. For an outside mount, measure the area you want covered, including any overlap. Then choose your control side and roll direction.

Rolli light-filtering roller shades inside-mounted in an editorial Austin living room

Before you measure

Inside or outside?

An inside mount sits within the window frame for a clean, built-in look. An outside mount covers the frame and blocks more light at the edges. Not sure? Read the three options below before you pick up the tape.

What will the brackets hit?

Wood trim and framing are the easiest surfaces. Drywall needs anchors. Tile, stone, metal and vinyl frames need the right fasteners, so note the surface for each window.

Corded or motorized?

Motorized shades remove cords entirely, which makes them safer around children and pets and easier to reach on tall or hard-to-reach windows. Choose motorization when you configure your shade.

Seen the fabric in person?

Color and opacity shift with your light. Order fabric samples and hold them against the window at different times of day before you commit.

Measure your window

Choose the mount that matches your window. Each one needs only two numbers, width and height, measured a specific way.

Inside mount

Built-in lookShows off trimFits between two walls
  1. Check the depth

    Measure from the glass (or the nearest obstruction, like a crank or lock) to the front edge of the frame. You need at least 2″ between the window pane and the front edge of the window frame. This will allow the brackets to fit properly inside. Too shallow? Switch to an outside mount.

  2. Measure width in three places

    Measure the inside of the frame, edge to edge, at the top, middle and bottom. Write down the narrowest of the three, to the nearest 1/8″. If you need to round off, round down to the nearest 1/8″.

  3. Measure height in three places

    Measure from the top inside of the frame to the sill at the left, center and right. Write down the longest of the three, to the nearest 1/8″.

Do not subtract anything. We take the clearance deduction at the factory so the shade fits the opening. The fabric runs slightly narrower than the headrail, so expect a small light gap on each side.

W1W2W3 H1H2H3 Order: narrowest W × longest H
Measure inside the frame. Three widths, three heights.

Outside mount on trim

Bedrooms & media roomsBest light controlShallow frames
  1. Find a flat mounting surface

    Brackets need about 2″ of flat surface on the face of the trim or the wall above it. Check for crown molding, alarm sensors or vents in the way.

  2. Measure the width

    Measure across the top, from the outside edge of the trim to the outside edge on the other side. For more privacy and less edge light, add 1″–2″ per side.

  3. Measure the height

    Measure from where the brackets will sit down to where the shade should stop: the sill, the bottom of the apron, or a line that matches other shades in the room.

Give us the exact size you want the shade to be. Outside-mount shades are made to your width and height with no deduction.

Width: trim edge to trim edge Height Brackets mount on the face of the trim
The shade covers the trim. Measure the outside edges.

Outside mount with no trim

Drywall returnsModern, trimless openingsCovers obstructions
  1. Measure the opening

    Measure the width of the drywall opening at its widest point and the height from the top of the opening to the sill or bottom edge.

  2. Add overlap to the width

    Add at least 2″ per side (4″ total) so the shade covers the opening and blocks edge light. Add 3″ per side for a bedroom.

  3. Add room for the brackets

    Add 2″–3″ above the opening for the brackets and roller, plus 1″–2″ below if there is no sill.

Your order width and height are the opening plus the overlap. Mount brackets into studs or with drywall anchors rated for the shade's weight.

Opening + 2″ to 3″ each side +2″+2″ Brackets mount on the wall above the opening
Overlap on every side gives the best light control.

Size calculator

Enter your measurements in inches. Fractions work: type 34 3/8 or 34.375. The calculator gives you the numbers to enter when you order.

Order width

—

Order height

—

If the calculator does not respond, order the narrowest width and the longest height you measured (inside mount), or the opening plus your overlap (outside mount).

Control side & roll direction

Control side

Left or right

Facing the window from inside the room, choose the side where the cord loop or motor sits. Pick the side you can reach easily, away from furniture, and where the control will be least visible. For two shades side by side, put the controls on the outer edges.

Roll direction

Standard or reverse roll

Standard roll: fabric drops behind the roller, close to the glass, for the least light gap. Reverse roll: fabric rolls off the front and hides the roller, and clears cranks, locks and handles that stick out from the frame.

Standard Reverse
Light-filtering roller shades half lowered in a styled New York living room

Measure like a pro

  • Use a steel tapeCloth and vinyl tapes stretch. A steel tape stays accurate over long spans.
  • Label every numberWrite W and H next to each measurement, width first. A swapped width and height is the most common ordering mistake.
  • Round to 1/8″Measure to the nearest 1/8″. Do not round to the nearest inch or half inch.
  • Measure every windowWindows that look identical often differ by 1/4″ or more. Measure and label each one by room.
  • Never deductGive us exact inside measurements. We handle the clearance deduction for inside mounts.
  • Check for obstructionsNote cranks, locks, alarm sensors and tilt latches. They decide your depth, mount and roll direction.

Common questions

Should I choose inside or outside mount?

Choose inside mount for a clean look when your frame has enough depth . Choose outside mount for maximum darkness, shallow frames, or when obstructions sit inside the frame.

Why use the narrowest width and the longest height?

The narrowest width makes sure the shade fits at every point in the frame. The longest height makes sure the fabric reaches the sill everywhere.

My window is very wide. What now?

Check the maximum width on the product page. Wider openings can use two or more shades side by side. Call us and we will help you split the width evenly.

Can Rolli measure for me?

Call a Rolli specialist at 833-447-6554. We can walk you through every window and talk through professional measuring for your project.

What if I measured wrong?

Call us as soon as you notice. Every shade is cut to order, so double-check every number against this guide before you check out.

Measured? Now design yours.

Choose your fabric, mount, control and motorization, then enter your width and height. Every Rolli shade is made to your exact size.

Questions? We're here.

Call 833-447-6554

Showroom: 2307 Thornton Rd, Suite 108-1, Austin, TX 78704

Sunlight, Solved.