
Install guide · Roller shades
How to install roller shades
A roller shade takes about 10 to 20 minutes to install. Hold each bracket in a top corner, mark two level screw holes, pre-drill, screw the brackets in and click the shade into place, control end first. Chain-operated shades finish with a cord tension device for child safety. Motorized shades skip the chain and pair to their remote instead.
Before you start
- Time
- 10 to 20 minutes per shade
- People
- 1, or 2 for wide or heavy shades
- Tools
- Cordless drill with a Phillips bit, 1/8″ drill bit, pencil, level, tape measure, safety glasses, step ladder
- Units
- Inches, to the nearest 1/8″
Before you start
Check the delivery against your order
Unpack on a clean surface and compare the width, height and mount type on the label with your order confirmation before you drill anything. If something does not match, tell us right away and hold off on installing.
Confirm the control side
Your order confirmation names the side the chain or motor sits on, looking at the window from inside the room. The control bracket goes on that side. Check it now, not after the holes are drilled.
Get a second pair of hands for wide shades
A shade over about 6 feet wide is awkward to hold level while you click it in. Plan on two people for large or heavy shades, and for anything high enough to need a tall ladder.
Look before you drill
Check the window area for wiring, alarm sensors, pipes and tile. Clear the sill and move furniture back so the ladder sits on flat, stable floor.
Your kit
Everything below should be in the box. Tick it off before you climb the ladder. Leave the protective wrap on the fabric until the shade is in its brackets.
- Roller shadeFabric rolled on its tube, with the control end and the pin end already fitted
- Control bracketTakes the chain clutch or the motor end
- Pin-end bracketTakes the spring-loaded pin at the other end
- ScrewsFor wood. Drywall and masonry need anchors (see below)
- Cord tension device and screwsChain-operated shades only. Required, not optional
- Ball stopClear clip that sets the lowest point of the chain
- Bracket coversOutside mounts only
- Cassette or fascia with returns or spring clipsOnly if you ordered one
- Remote and charging cableMotorized shades only. Charge the motor before you install
- Your toolsDrill, 1/8″ bit, Phillips bit, level, pencil, tape, safety glasses, ladder
What you are drilling into
The screws in the box are for wood. Anything else needs the right anchor, so identify your surface first.
Wood
Trim, window frames and headers
The simplest case. Pre-drill with the 1/8″ bit and drive the supplied screws straight in. Wood shavings on the bit confirm you are in solid wood.
Drywall
Find a stud or use an anchor
Run a stud finder along your bracket line. Where a bracket lands on a stud, use the supplied screws. Where it does not, use self-drilling drywall anchors or toggle bolts rated well above the weight of the shade. Skip the small plastic plugs that come with picture hooks.
Concrete, brick, stone or tile
Masonry bit and masonry anchors
Switch to a hammer drill with a masonry bit sized to your anchors, then fit plastic or sleeve anchors rated for the load. On tile, start the hole with a tile bit and light pressure so the glaze does not crack.
Not sure?
Call before you drill
Vinyl window frames, aluminum frames, plaster-and-lath walls and steel framing each need a different approach. Call a Rolli specialist at 833-447-6554 and describe what you have. We will tell you what fasteners to use.
Install the shade
Pick the fit you ordered. All three follow the same six steps. Only where the brackets go changes.
Outside mount on trim
Get organized
Unpack the shade on a clean floor under the window and lay the brackets, screws and tension device beside it. If you ordered a cassette or fascia, slip the brackets into its end returns now so the whole assembly goes up in one piece. Check your order confirmation for the control side.
Mark the holes
Hold the control bracket on the trim at the top corner on the control side, with the bracket flush with the outer edge of the trim and its top edge where you want the top of the shade. Set a level on it and pencil both screw holes. Measure across to the other corner and mark the pin-end bracket at exactly the same height, flush with the far edge. The outside edges of the two brackets should match the ordered width of the shade.
Attach the brackets
Put on safety glasses and pre-drill each mark with the 1/8″ bit, about 1″ deep. Hold the control bracket over its holes and drive both screws. Repeat for the pin-end bracket. If a fascia is fitted, screw it up as one unit the same way.
Click in the shade
Turn the shade so the chain hangs on the control side and the small cover on the control end points straight up. Slot the control end into its bracket first. Then push the pin end into the far bracket until you hear it click. Tug the fabric gently to confirm both ends are seated.
Fit the cord tension device
Chain-operated shades only. Lower the shade fully, clip the tension device over the bottom of the chain loop and slide it down the trim or wall until the chain is just taut. Mark the holes, pre-drill and screw it in. Motorized shades skip this step.
Finish
Slide the bracket covers on. If you ordered a cassette or fascia, clip one end on, then the other. Set the ball stop and test the shade as described below.
Deep or decorative trim can tilt a bracket out of true. If the trim profile is not flat, mount the brackets on the wall above the trim instead and follow the no-trim tab.
Outside mount, no trim
Get organized
Unpack the shade on a clean floor under the window and lay out the brackets, screws and tension device. If you ordered a cassette or fascia, slip the brackets into its returns now. Check your order confirmation for the control side.
Mark a level line
Decide how high the shade will sit. Two to three inches above the opening is typical, and it hides the roll from view. Measure up from the top of the opening at both sides, connect the marks with a level and draw a light pencil line. Center the ordered width on the window so the shade overlaps the opening by the same amount on each side, and mark where each bracket's outer edge falls.
Attach the brackets
Hold the control bracket on your line on the control side and pencil both screw holes. Run a stud finder over each mark. Put on safety glasses, pre-drill with the 1/8″ bit, fit anchors if there is no stud, then drive the screws. Repeat for the pin-end bracket, checking the level again before the second screw goes in.
Click in the shade
Turn the shade so the chain hangs on the control side and the small cover on the control end points straight up. Slot the control end into its bracket first, then push the pin end into the far bracket until it clicks. Tug the fabric gently to confirm both ends are seated.
Fit the cord tension device
Chain-operated shades only. Lower the shade fully, clip the tension device over the bottom of the chain loop and slide it down the wall until the chain is just taut. Mark, pre-drill, anchor if needed and screw it in. Motorized shades skip this step.
Finish
Slide the bracket covers on. If you ordered a cassette or fascia, clip one end on, then the other. Set the ball stop and test the shade as described below.
On drywall, the two bracket screws rarely both land on a stud. One screw in a stud plus one rated anchor is fine. Two anchors are fine too, as long as they are rated for the weight.
Inside mount
Get organized
Unpack the shade on a clean floor under the window and lay out the brackets, screws and tension device. If you ordered a cassette, slip the spring clips or brackets into it now. Check your order confirmation for the control side, and confirm the opening is deep enough for the bracket to sit fully inside it.
Mark the holes
Hold the control bracket up inside the top corner of the opening on the control side, pushed to the side jamb. Slide it forward or back so the rolled fabric will hang 3/8″ to 1/2″ clear of the glass and any window locks or handles. Pencil both screw holes. Repeat at the other corner for the pin-end bracket, at exactly the same depth, so the shade hangs square to the glass.
Attach the brackets
Put on safety glasses and pre-drill each mark with the 1/8″ bit. Hold the control bracket over its holes and drive both screws. Repeat for the pin-end bracket. On a vinyl or aluminum window frame, drill into the wood or drywall of the opening, not the window frame itself.
Click in the shade
Turn the shade so the chain hangs on the control side and the small cover on the control end points straight up. Slot the control end into its bracket first. Then press the pin end into the far bracket until it clicks. If it will not go, the pin is spring-loaded: push it in with a fingertip as you lift the shade into place.
Fit the cord tension device
Chain-operated shades only. Lower the shade fully, clip the tension device over the bottom of the chain loop and slide it down the side jamb until the chain is just taut. Mark, pre-drill and screw it to the jamb. Motorized shades skip this step.
Finish
If you ordered a cassette, clip it over the brackets now. Set the ball stop and test the shade as described below. Inside mounts do not use bracket covers.
A little daylight at each side of an inside mount is normal. The fabric is narrower than the tube so it can roll without rubbing on the opening. If you want full coverage, an outside mount is the answer.
Child safety
Read this before you finish a chain-operated shade
A looped chain can strangle a child. The US window covering safety standard calls for a cord tension device on every continuous-loop chain, and we include one with every chain-operated Rolli shade. Install it. A shade without its tension device is not finished.
- Fit the tension device so the chain is held taut against the wall or jamb and cannot form a loose loop.
- Keep cribs, beds, chairs and anything a child can climb away from the chain.
- Do not remove the warning tags from the chain or the shade.
- For nurseries and children's rooms, choose a motorized or cordless shade. There is no chain to manage.
Finish and test
Pull the protective wrap off the fabric and run the shade down and back up once. It should roll smoothly, hang square and stop where you want it.
Set the ball stop. Lower the shade to the lowest point you want it to reach. Find the chain that runs toward the window on a standard back roll, or the chain nearest the room on a reverse roll, and click the clear ball stop onto it just above the clutch. The shade will now stop there every time.
Bracket covers and cassettes. Outside-mount bracket covers slide straight over the brackets. A cassette or fascia clips on at one end, then the other; a firm, even push seats it.
Motorized shades. Charge the motor fully before you hang the shade, then follow the card in the box to pair the remote and set the upper and lower limits. Run the shade through a full cycle from the remote before you put the ladder away.
Give it a week. A shade that has been rolled tight in a box can show a slight curve or a tendency to drift. Daily use and warm weather settle it. Vary the height you leave it at for the first few days.
Install like a pro
- Control end firstSlot the control end into its bracket before the pin end. The pin is spring-loaded and clicks home; the control end does not, so it needs to be seated first.
- Cover upThe small cover on the control end should point straight up when the shade is in. If it is rotated, the shade will roll hard or clunk.
- Pre-drill, alwaysA 1/8″ pilot hole stops the screw from wandering and keeps trim from splitting.
- Read the drillWood shavings mean solid wood. White dust means drywall only, so fit a rated anchor before you drive the screw.
- Level the brackets, not the shadeA shade can only hang as true as its brackets. Check the level on the bracket before the second screw goes in. Fixing it later means taking the shade down.
- Same depth, both sidesOn an inside mount, two brackets at different depths twist the tube and make the fabric track to one side.
- Keep the wrap onLeave the protective wrap on the fabric until the shade is clicked in. It keeps fingerprints and drill dust off a light fabric.
Troubleshooting
The shade is hard to roll, or it clunks.
The control end is probably rotated. Take the shade down: turn the clear cog on the pin end counter-clockwise to retract the pin, lift that end out, then free the control end. Turn the shade so the small cover on the control end points straight up and click it back in, control end first.
The fabric tracks to one side.
First check that both brackets are level and, on an inside mount, at the same depth. If they are, roll the fabric all the way up to expose the bare tube and stick a 2″ strip of masking tape on the tube on the side the fabric should move toward. Roll it down and up. Add a layer at a time until it runs straight.
The pin end will not click into its bracket.
Check that the control end is fully seated first. Then push the pin in with a fingertip as you lift the pin end into the bracket. If the brackets are too far apart or too close together, measure the gap against the ordered width and move one bracket.
The fabric has a curve or a kink.
Lower the shade fully and leave it for a day or two. The weight of the fabric and a warm room pull most packing marks out. Vary the height you leave the shade at over the first week.
I want the chain on the other side.
Take the shade down, swap the control end and the pin end on the tube, and reinstall with the control bracket on the new side. If you would rather not, call us at 833-447-6554 and we will talk you through it.
How do I clean the fabric?
Dust with a soft cloth or a vacuum brush on low. For marks, dab with a damp cloth and mild soap. Do not rub, and do not soak the fabric. Check the care note that came with your shade first.
How do I take the shade down to paint or redecorate?
Turn the clear cog on the pin end counter-clockwise to retract the pin, lift that end out, then free the control end. Leave the brackets in place and click the shade back in afterward, control end first.
The shade does not fit the window.
Stop before you drill and call us at 833-447-6554. Have your order number and the measurements from our roller shade measuring guide ready and we will sort it out.
Can Rolli install for me?
Call a Rolli specialist at 833-447-6554. We can talk through your project and professional installation options in your area.
Still choosing fabric? Start here.
Every Rolli roller shade is made to your window, your mount and your control. Measure first, then choose your fabric and opacity.
Questions? We're here.
Call 833-447-6554
Showroom: 2307 Thornton Rd, Suite 108-1, Austin, TX 78704
Sunlight, Solved.








